I understand that there are two variants of the 2000-2002 Camry. If reusing the timing belt, check that there are 4 installation marks on the timing belt as shown in the illustration. How many miles are on the motor with the broken belt? Many engines vary a bit in that regard. I was not aware that the distinction of a belt or a chain translated through to the ability of the pistons and valves to run into one another. If the idle speed is increases by more 100 rpm, using a 4 mm hexagon wrench, turn the idle—up valve adjustment screw to correct the idle—up valve. If the oil clearance is greater than maximum, replace the bearings. .
Torque: 30 N—m 300 kgf—cm, 22 ft—lbf 23. Heres some reference material for you. Torque: 8 N—m 80 kgf—cm, 69 in. I have a 2000 Avalon. I decided to sell it cheap and maybe look for a 2000-2002 Camry instead. Sensor 1 refers to the sensor closer to the engine body. If any movement is felt, replace the piston and pin as a set.
Repair or replace harness or connector. Torque: 43 N—m 440 kgf—cm, 32 ft—lbf 10. If any of the connecting rod cap bolts is broken or deformed, replace it. It may need a replacement. I have talked to some former auto technical people who say it isn't. Terminals 3 and 5 Open Continuity Terminals 1 and 2 Reference value 72W 1 Apply battery voltage between terminals 1 and 2.
Difference between each injector: Less than 6 cm 0. That said, I don't recommend waiting to find out whether I am correct or not! Inspect piston pin oil clearance a Using a caliper gauge, measure the inside diameter of the connecting rod bushing. I think that even with 10 years use of my car by two previous owners but only 72K of mileage on the car, I should be alright until then. This engine has been phased out in most markets, replaced by variants of the new series. As mentioned you should be ok since it is a non-interference engine. Don't really trust other mechanics anymore. Maximum warpage: Air Intake Chamber Side 0.
No activated carbon should come out. Torque: 21 N—m 210 kgf—cm, 16 ft—lbf 2. Horsepower ratings dropped after the implemented a new power measurement system for vehicle engines, Toyota engines rated on 87 octane dropped the most, compared to the same engines used by Lexus rated on 91 octane. Torque: 43 N—m 440 kgf—cm, 32 ft—lbf b Check that the idler pulley moves smoothly. Install the timing belt in this order. I might have to do it over once or twice until it's perfect, but that is not hard to do. Visually check for cracks and breaks on the gasket of the timing belt cover.
I don't travel that much; and, I won't have the money for my local Toyota agency to replace the timing belt until early January 2008. Or in my opinion anyway. Check resistance of heated oxygen sensor heater. Measure resistance of camshaft position sensor. So on this note, is there a comprehensive list of Toyota's or any vehicles where you can find out if they're interference or not? If any of the main bearing cap bolts is broken or deformed, replace it. It makes sense because logic says a chain is stronger so it would be used where there could be a problem if it broke, and a belt would be used in applications where it wouldn't matter to the valves if it broke. From what I have ready and have had no negative reports, the 2.
Temperature value: 120 C 248 F or more Confirm good connection at sensor. I have a 2002 Corolla -- it's a chain -- is it interference? Uni— formly tighten the bolts in several passes. Torque: 29 N—m 300 kgf—cm, 22 ft—lbf t Reconnect the negative — terminal cable to the battery. I thought the decision of belts vs. I was not aware that the distinction of a belt or a chain translated through to the ability of the pistons and valves to run into one another. Injection time fixed Returned to normal condition Starting.
Remove the 0—ring and grommet from each injector. In many cases, by carrying out the basic engine check shown in the following flow chart, the location causing the problem can be found quickly and efficiently. In this state, check to see that there are no leaks from any part of the fuel system. Check voltage terminal 3 of circuit opening relay. That is if the timing belt breaks, do I incur cylinder head damage interference type or just a loss of power but no head damage non-interference.
If it is regularly maintained and smoothly run, the motor is quite safe and serves long. Temperature value: — 40 C — 40 F. Install timing belt guide No. The solenoid valve adjusts the volume of oil sent from the hydraulic pump to the hydraulic motor which drive; the fan directly, thereby controlling the fan speed. Just curious about your info.
Belts ought to be cheaper too. I think that even with 10 years use of my car by two previous owners but only 72K of mileage on the car, I should be alright until then. If rear oil seal retainer is removed from cylinder block: a Using a screwdriver and hammer, tap out the oil seal. If the thrust clearance is greater than maximum, re—. Trouble Area Voltage output of the heated oxygen sensor bank 1 sensor 2 remains at 0. This is an area that really needs some definitive clarification by a knowledgable person, like an automotive engineer for example.